Ankündigung

Einklappen
Keine Ankündigung bisher.

Reset value from DoorBird Motion

Einklappen
X
 
  • Filter
  • Zeit
  • Anzeigen
Alles löschen
neue Beiträge

  • Reset value from DoorBird Motion

    I have integrated my DoorBird into my Loxone project. I use the http-calls for doorbell and motion as virtual inputs.
    In addition I want my exterior light to brighten up when someone comes up to my house and gets detected by the DoorBird Motionsensor.

    The problem is, that the http-call gives 1 as value when motion is detected and this value never changes in Loxone. It just stays 1. How can I achieve that the value from this virtual input is set back to 0 when there is no motion detected in a periode of time? (in DoorBird, there is a 30 second margin set between two alarms).

  • #2
    Set the VI to Digital.
    Don’t send “1”, but send “Pulse”.
    As the pulse is very short (you might not see it in LiveView), connect something like a Monoflop that you can see and test the pulse.
    Hilfe für die Menschen der Ukraine: https://www.loxforum.com/forum/proje...Cr-die-ukraine

    Kommentar


    • #3
      I use this SIP-call:

      event=motionsensor&subscribe=1

      I thought I could replace the subscribe=1 with subscribe=pulse but that is not a valid syntax.

      Kommentar


      • #4
        Don’t know what this means...
        I was talking about the Loxone Web API.
        Hilfe für die Menschen der Ukraine: https://www.loxforum.com/forum/proje...Cr-die-ukraine

        Kommentar


        • #5
          To forward the motion and doorbell events from DoorBird to Loxone, I had to activate SIP in DoorBird and register these two events by entering these url's in my browser:

          http:// <doorbird-username>:<doorbird-password>@<doorbird-ip-adress>/bha-api/notification.cgi?url=http://<loxone-miniserver-ip-address:<loxone-miniserverport>/dev/sps/io/viXX/pulse?motionsensor&user=<loxone-miniserver-username>&password=<loxoneminiserver-password>&event=motionsensor&subscribe=1

          http:// <doorbird-username>:<doorbird-password>@<doorbird-ip-address>/bha-api/notification.cgi?url=http://<loxone-miniserver-ip-address>:<loxone-miniserverport>/dev/sps/io/viXX/pulse?doorbell&user=<loxone-miniserver-username>&password=<loxoneminiserver-password>&event=doorbell&subscribe=1

          Where viXX is the connection-name of the virtual inputs in my Loxone config that I use to trigger the action.
          Zuletzt geändert von Bart; 10.11.2020, 13:57.

          Kommentar


          • #6
            The Loxone API does not support query parameters.

            If you use a LoxBerry, you may try the generic url-to-mqtt interface (use Translate):


            Regards, Christian
            Hilfe für die Menschen der Ukraine: https://www.loxforum.com/forum/proje...Cr-die-ukraine

            Kommentar


            • #7
              Hello,
              has anyone possibly found a simple solution to use the Doorbird (d1101v) motion detector for e.g. the outdoor lighting with SIP configuration?

              Thanks, Jörg
              ----------------------------------
              Hallo, hat irgend jemand eventuell inzwischen eine einfache Lösung gefunden, bei SIP Konfiguration den Doorbird Bewegungsmelder für die Außenbeleuchtung zu verwenden?

              Danke, Jörg

              Kommentar

              Lädt...
              X